Single Sided Protective Coil
video

Single Sided Protective Coil

Our factory supplies premium single sided protective coil (single-sided grommet / one-side flange rubber grommet / push-fit snap-in cable grommet) — a standard cable protection component featuring a flange on only one side, designed to be pushed into a pre-drilled panel hole from one side. The single-sided flange enables tool-free installation in enclosed cabinets and one-side-access panels where double-sided grommets cannot be used. Made from high-quality rubber (standard NBR, with EPDM, CR, silicone and FKM options), these grommets protect wires and cables passing through panel holes from sharp edges, while providing electrical insulation, dust sealing and vibration damping. Available in 30+ standard sizes (ID 3mm-100mm), multiple hardness levels (Shore A 40-80), multiple colors, with optional flame-retardant (UL94 V-0) and food-grade (FDA) grades, and fully customizable dimensions.
Send Inquiry
Product Introduction

Product Specifications

 

Our factory supplies premium single sided protective coil (single-sided grommet / one-side flange rubber grommet / push-fit snap-in cable grommet) - a standard cable protection component featuring a flange on only one side, designed to be pushed into a pre-drilled panel hole from one side. The single-sided flange enables tool-free installation in enclosed cabinets and one-side-access panels where double-sided grommets cannot be used. Made from high-quality rubber (standard NBR, with EPDM, CR, silicone and FKM options), these grommets protect wires and cables passing through panel holes from sharp edges, while providing electrical insulation, dust sealing and vibration damping. Available in 30+ standard sizes (ID 3mm-100mm), multiple hardness levels (Shore A 40-80), multiple colors, with optional flame-retardant (UL94 V-0) and food-grade (FDA) grades, and fully customizable dimensions.

 

Full parameters below:

Item

Detailed Parameters

Product Name

China Single Sided Protective Coil, One-Side Flange Rubber Grommet, Push-Fit Snap-In Installation, Cable Wire Hole Protection, Insulation Dustproof Seal, NBR/EPDM/Silicone Material, Custom Size & Hardness, for Electrical Cabinet, Automotive, Appliance & Machinery

Material Options

Standard: NBR (nitrile rubber) - excellent oil/abrasion resistance, cost-effective, general industrial use; EPDM - excellent weather/ozone/UV resistance, waterproof, good electrical insulation, outdoor use; CR (neoprene) - good oil/weather/flammability resistance, versatile; Silicone (VMQ) - wide temp range (-60℃ to +230℃), food-grade option, high-temp use; FKM (Viton) - excellent chemical/oil/heat resistance, premium harsh-environment grade; Custom formulations available

Hardness (Shore A)

Standard: 60±5 Shore A (most common); Available: 40 Shore A (very soft, delicate cables) to 80 Shore A (firm, heavy cables, high vibration); Custom in 5-degree increments; Tolerance ±5 Shore A

Size Range (Stock Sizes)

Inner diameter (cable hole): 3mm to 100mm (30+ standard sizes); Mounting hole diameter: 6mm to 120mm+; Outer diameter (flange OD): 10mm to 150mm+; Height/thickness: 3mm to 20mm; Flange thickness: 1mm to 3mm; Custom sizes from 2mm ID to 200mm+ OD; Provide panel hole diameter, panel thickness and cable OD for size recommendation

Design & Structure

Single-sided flange on ONE side only - rests flat against panel surface; Open through-hole; Tapered leading edge for easy insertion; Elastic body compresses and locks in place; Smooth rounded inner bore (no sharp edges); Optional: blind/closed version, multi-hole version, stepped bore, ribbed version, rubber-to-metal bonded

Key Features

Single-sided flange - install from ONE side only, ideal for enclosed/inaccessible panels; Push-fit snap-in - no tools, no adhesive, no screws, 2-5 sec installation; Cable protection - smooth inner bore prevents insulation cut-through and short circuits; Electrical insulation - rubber insulates cable from metal panel; Dust/contaminant seal - elastic body seals panel hole; Vibration damping - reduces cable fatigue, prevents loosening; Temp range: NBR -30~120℃, EPDM -40~150℃, Silicone -60~230℃, FKM -20~200℃; Oil resistance (NBR/CR/FKM excellent); Weather/UV resistance (EPDM excellent); Flame-retardant UL94 V-0 option; Food-grade FDA option (silicone); Multiple colors; Standard sizes in stock (3-5 day shipping); Fully customizable; RoHS, REACH, ISO 9001 compliant

Color Options

Standard: Black; Stock: White, Gray, Red, Blue, Green, Yellow, Orange; Custom: Pantone color matching (MOQ applies); Color-coding for cable type/voltage identification

Applications

Electrical: cabinets, distribution boxes, control panels, junction boxes, switchgear, PLC enclosures; Automotive: body panels, firewall pass-through, wiring harness, marine/RV electrical; Appliances: refrigerator, washer, oven, AC, power tools, vacuum; Machinery: machine tools, conveyors, packaging, food/pharma equipment; Instruments: test & measurement, medical devices, audio/video, IT/telecom, CCTV; Building: conduit fittings, junction boxes, lighting, HVAC, solar junction boxes, elevators; DIY/custom enclosures

Certifications

RoHS, REACH, ISO 9001, UL94 V-0 (flame-retardant option), FDA 21 CFR 177.2600 (food-grade silicone option), SGS test reports (hardness, tensile, elongation, tear, compression set, oil/temp resistance, flammability)

MOQ & Stock

Standard sizes (black NBR, 60 Shore A): MOQ 100 pieces, IN STOCK, ships 3-5 days; Custom sizes/colors/materials: MOQ 1,000-5,000 pieces per size (mold fee applies, refundable for 50,000+ orders); Custom color of stock sizes: MOQ 500 pieces; OEM & ODM supported

Packaging

Standard: PE bags (100/500/1000 pcs/bag), reinforced corrugated cartons, fumigation-free pallets for export; Custom: individual retail packaging (header card, blister, color box), custom labels with part numbers/batch codes, custom carton markings

 

Product Introduction

 

The single sided protective coil (single-sided grommet / one-side flange rubber grommet) is a standard cable protection component installed in pre-drilled panel holes. It features a flange (retaining lip) on only one side, unlike double-sided grommets which have flanges on both sides. This single-sided design is the key to its versatility: the grommet can be installed from only one side of the panel - simply align with the hole and push in. The elastic rubber body compresses through the hole, then expands to lock securely, with the flange resting flat against the panel surface. The back side need not be accessible - a critical advantage in enclosed electrical cabinets, welded assemblies, deep housings and wall-mounted panels where double-sided grommets are impossible to install. Unprotected cable holes cause insulation cut-through from sharp metal edges, leading to short circuits, equipment failure and fire hazards. The single sided protective coil solves this with a smooth rounded rubber inner bore that protects cables, while the elastic body seals against dust and contaminants, provides electrical insulation, and dampens vibration. Standard sizes (ID 3mm-100mm, black NBR 60 Shore A) are in stock for fast shipping (3-5 days), with custom materials (NBR/EPDM/CR/Silicone/FKM), hardness (40-80 Shore A), colors and special features available for OEM applications - making it the most widely used cable protection component across electrical, automotive, appliance, machinery and electronics industries.

Core Selling Points

Single-sided flange - install from one side only, ideal for enclosed panels: The defining feature is a flange on only one side, enabling installation from the accessible side without reaching the back. The elastic body compresses through the hole and expands to lock, with the flange resting flat against the front surface. This is impossible with double-sided grommets (require two-side access) and most cable glands. Ideal for enclosed cabinets, welded assemblies, deep equipment housings, wall-mounted panels and one-side-access applications. The single flange also provides a clean, finished appearance.

Push-fit snap-in - no tools, 2-5 seconds per grommet: Installation requires no tools, adhesive or screws - simply push into a pre-drilled (and deburred) hole. The tapered leading edge guides insertion, the elastic body compresses and snaps into place. At 2-5 seconds each, this is 10-30x faster than screw-type cable glands (30-60 sec), reducing assembly labor cost. No torque specifications, no stripped threads, no curing time. Installation quality is consistent regardless of worker skill. Grommets are removable and reusable (push out from back or pry from front).

Smooth rounded inner bore - protects cable insulation, prevents short circuits: The primary function is protecting wires and cables from sharp panel edges. The smooth, rounded, soft rubber inner bore ensures cables contact rubber, not sharp metal - eliminating insulation cut-through, short circuits, ground faults and fire hazards. Especially critical in high-vibration environments (automotive, machinery) where cable movement against hard edges causes failure in months. The smooth bore also makes cable pulling easier with less friction. Required by electrical codes (UL 508A, NEC Article 300.4, IEC 60204-1) in many applications.

Elastic dust seal + electrical insulation + vibration damping: Three additional functions in one component: (1) Dust/contaminant seal - the elastic body (0.5-1.5mm interference fit) compresses against the hole wall, preventing dust, dirt, fibers and insects from entering; provides IP54-level splash protection with proper cable fit. (2) Electrical insulation - rubber (volume resistivity >10^12 Ω·cm) insulates cable from metal panel, preventing accidental grounding and shock hazards. (3) Vibration damping - rubber absorbs vibration, reducing cable fatigue and preventing the grommet from working loose. Metal and plastic grommets cannot match all three functions.

Multi-material / multi-hardness versatility + standard stock sizes: 5 material options cover every environment: NBR (general indoor/oil, -30~120℃), EPDM (outdoor/weather/high-voltage, -40~150℃), Silicone (high-temp/food/medical, -60~230℃), FKM (chemical/harsh, -20~200℃), CR (versatile all-around). Hardness 40-80 Shore A: soft for delicate cables, firm for heavy cables/high vibration. 30+ standard sizes (ID 3mm-100mm) in stock, MOQ 100 pieces, ships 3-5 days. Custom sizes, materials, hardness, colors and features (flame-retardant, blind, multi-hole) available with 10-15 day lead time. Suitable for everyone from DIYers to high-volume OEMs.

Solutions for Buyer Concerns

Factory-direct transparent pricing: As an original manufacturer, we control the entire chain from compounding, mold making, molding, deflashing to inspection and packaging. Tiered volume discounts with no hidden fees. Standard stock sizes offer lowest pricing and fastest shipping; custom sizes priced transparently by material, size and volume. Competitive against metal/plastic grommets and cable glands - with superior performance and lower total cost (no tools, faster install, reusable).

Rigorous quality inspection & certification: Each lot undergoes raw material testing (FTIR composition, hardness, tensile, elongation, tear, compression set, oil/temp resistance), dimensional inspection (ID/OD/hole/height, ±0.1mm tolerance), visual inspection (no flash, burrs, cracks, porosity), installation fit test (push-in/pull-out force on test panels), functional test (cable pass-through, smooth inner bore), and batch traceability with COC. Full SGS reports available. UL94 V-0 and FDA grades certified accordingly.

Protective packaging & flexible logistics: PE bags (100/500/1000 pcs) with labels (name, material, hardness, size, quantity, batch, date), then reinforced cartons or fumigation-free pallets for export. Custom retail packaging (header card, blister, color box), custom labels and carton markings available. Sea/air/express options balancing speed and cost. Standard stock ships 3-5 days.

Precision molding & compounding craftsmanship: State-of-the-art compression/injection molding with precise temp/pressure/cycle control ensures consistent curing, dimensional accuracy and surface finish. In-house compounding with controlled ingredient ratios and mixing ensures consistent material properties across batches. In-house CNC/EDM mold making ensures accurate cavities, smooth finish, proper draft angles and minimal flash. Compared to cheap alternatives (inconsistent dimensions, rough inner bore, poor material quality, excessive flash, batch variation), our product maintains consistent quality and reliable performance in every batch.

Competitive Advantages & Peer Comparison

Alternative cable protection solutions each have significant drawbacks. Double-sided grommets provide a secure hold but require two-side access (impossible in enclosed panels), are harder to install, cost more, and cannot be removed from one side. Metal grommets (brass/aluminum/steel) are durable but have hard inner surfaces that abrade cables, are not electrically insulating, can corrode, require threading/crimping tools, and provide no vibration damping. Plastic grommets (PA/PP) are inexpensive but hard and brittle at low temps, poor vibration damping, limited temperature range (PA ~100℃), can crack on impact, and provide less effective sealing. Screw-type cable glands provide IP68 sealing and strain relief but require tools/threading, cost 3-10x more, require two-side access, and are overkill for many indoor cabinet applications (IP54 from a grommet is sufficient). Bare/ungrommeted holes are the worst - cable insulation cut-through, no dust/moisture seal, no insulation, no vibration damping. None deliver the balanced combination of one-side accessibility, tool-free push-fit installation, reliable cable protection, insulation, dust sealing, vibration damping, multi-material versatility, stock availability and cost-effectiveness that the single sided protective coil offers.

Usage, Installation & Maintenance

Installation: Select correct size (ID slightly larger than cable OD; mounting hole matches recommended diameter; grommet height > panel thickness by 1-3mm). Select material (NBR general, EPDM outdoor, silicone high-temp/food, FKM chemical) and hardness (60 standard, softer for delicate cables, firmer for heavy/high-vibration). Panel prep: drill correct diameter hole, deburr sharp edges, clean area. Install: align grommet (flange outward) with hole, push in by hand - elastic body compresses and snaps into place. For large/firm grommets, use gentle rocking or soft-faced mallet (with protective cloth). Verify flange is flat and grommet is secure (no rotation, no pull-out with moderate force). Then pass cables through bore - ensure adequate slack, do not overfill (70-80% max fill ratio).

Usage guidelines: Not for structural load-bearing, high-pressure sealing, or direct food contact (unless FDA silicone grade). Follow material temperature limits. Do not exceed max temp (causes hardening/cracking/seal failure). Do not expose to chemicals beyond material rating (NBR poor weather, EPDM poor oil, silicone poor oil/solvent). Do not expose to open flame/welding sparks (unless UL94 V-0 grade). Do not use sharp tools near grommet. Do not overfill bore. For outdoor/wet use, choose EPDM/silicone and ensure proper seal (cable gland for IP68 if needed). For high-vibration, use 70-80 Shore A. For high-voltage, use EPDM/silicone (better insulation).

Removal & replacement: From back side (if accessible): push out toward front - reusable. From front side: pry flange edge with flat screwdriver/plastic trim tool, work around to lift out - be careful not to scratch panel. Destructive: cut body with knife (protect cables/panel), peel out. After removal: inspect for damage (cracks, hardening, deformation, compression set, discoloration, oil swelling) - replace if damaged. Inspect panel hole for burrs/corrosion - re-deburr if needed. Inspect cables for insulation damage - repair/replace if needed. Service life: 5-10 years indoor, 3-5 years outdoor (material/environment dependent). Replace if signs of aging (hardening, cracking, deformation, discoloration, seal loss).

Storage & shelf life: Store cool (10-25℃), dry (40-70% RH), clean. Avoid direct sunlight, heat sources, ozone (near motors/welding/UV), high humidity, dust. Keep in original PE bags/sealed containers. Do not stack heavy objects on top (causes compression set, especially soft grades). Do not stretch/deform during storage. Keep away from oils/solvents/fuels and copper/manganese/iron metals. Shelf life: NBR/CR 3 years, EPDM/Silicone/FKM 5 years (proper storage). Test material properties after shelf life before use. FIFO inventory management.

 

Company Strength Display

 

We are a specialized rubber & silicone component manufacturer with extensive OEM/ODM experience for global electrical, automotive, appliance, machinery and electronics markets. Our facility houses rubber compounding lines, internal mixers, CNC mold machining, EDM, compression/injection molding presses, deflashing equipment, a material testing lab and a dedicated QC team - ensuring consistent capacity and batch quality for orders of any scale.

Production capacity: Multiple compression (100T-500T) and injection molding machines, daily output 50,000+ pieces. 30+ standard sizes (ID 3mm-100mm, black NBR 60A) in stock, ships 3-5 days. In-house mold design/manufacturing (CNC+EDM) in 5-10 days. In-house compounding for custom materials/hardness/colors. Secondary processing: cryogenic/tumble/manual deflashing, trimming, punching, cutting, rubber-to-metal bonding, custom assembly.

Certification system: RoHS, REACH, ISO 9001, UL94 V-0 (flame-retardant), FDA (food-grade silicone), SGS test reports. Satisfies import requirements for Europe, North America, Southeast Asia, Middle East and other markets. Full material test reports and COC with batch traceability for every lot.

R&D and customization: In-house engineering supports custom development: material formulation (custom NBR/EPDM/CR/Silicone/FKM, hardness 40-80A, Pantone colors, flame-retardant, food-grade, anti-static, conductive, high/low temp), custom dimensions (ID 2mm-200mm+, OD 5mm-300mm+), custom designs (blind, multi-hole, stepped, ribbed, strain relief, sealing lip, mounting tabs, metal-bonded), and performance optimization (pull-out force, sealing, cable protection, temp/chemical resistance). Turn drawing/sample into production in 10-15 days. Free material/design consulting and DFM feedback.

Packaging capability: Bulk PE bags, reinforced cartons, export pallets, custom labels, custom carton markings, individual retail packaging (header card, blister, color box). OEM bulk packaging with part number labeling and JIT delivery for manufacturing lines. Retail consumer packaging with installation instructions and size charts.

 

Pre-Sales & After-Sales Service

Pre-Sales Service

Our sales team provides comprehensive consultation on material selection (NBR/EPDM/CR/Silicone/FKM matching your environment), hardness selection (40-80A matching cable size/vibration), size selection (we recommend optimal size based on panel hole diameter, panel thickness and cable OD), color options, special features (flame-retardant, food-grade, blind, multi-hole, stepped), surface compatibility (metal/plastic/composite panels), application environment (indoor/outdoor, temp, humidity, oil/chemical, UV, vibration, voltage), stock availability, MOQ, pricing tiers, lead time, certifications and packaging. Free engineering consulting and sample evaluation (stock or custom prototypes) so you can verify material quality, dimensional accuracy, installation fit and cable protection before bulk ordering. Regulatory documentation (RoHS, REACH, UL94, FDA, SGS) and custom Pantone color matching available. For large OEM customers: dedicated account management, consignment stock, JIT delivery and continuous improvement support.

After-Sales Service

We are committed to long-term partnership. For confirmed factory-caused quality issues - material non-conformity, dimensional inaccuracy, installation fit problems (too loose/tight), material performance issues (cracking, hardening, swelling, compression set), visual defects (excessive flash, burrs, cracks, porosity), functional defects (sharp inner bore, poor sealing) or certification non-compliance - we offer replacement or refund. Our support team answers installation, removal, material/size selection, storage and troubleshooting questions (selecting size for specific panel/cable, improving pull-out force in high vibration, removing from enclosed panel, material for oil/chemical/UV exposure, preventing compression set in storage). For OEM customers: dedicated account management, production priority, proactive material notifications, consignment stock, JIT delivery and continuous improvement. For distributors: marketing materials (images, videos, certs, size charts, installation guides, SDS) and listing optimization support. Every lot undergoes rigorous inspection with full batch traceability. Contact support with order number, batch number and issue description (with photos) for prompt resolution.

 

FAQ

 

Q1: Single-sided vs double-sided grommets - what's the difference?

A1: Single-sided grommets have a flange on ONE side only - pushed in from one side, flange rests against front surface. Installable from one side only, ideal for enclosed cabinets and inaccessible back panels. Double-sided grommets have flanges on BOTH sides - require access to both sides (insert from one, pull rear flange from other). More secure hold but impossible in one-side-access applications. For most electrical cabinet/enclosure applications, single-sided is the standard choice due to one-side accessibility and easier installation.

Q2: How to choose the right size?

A2: Three key dimensions: (1) Inner diameter - slightly larger than cable OD (1-3mm clearance for single cable; multiple cables total cross-section ≤70-80% of bore area). (2) Mounting hole diameter - panel hole matches grommet's recommended size (grommet body OD typically 0.5-1.5mm larger than hole for interference fit). Refer to size chart. (3) Panel thickness - grommet height slightly greater than panel thickness (1-3mm) for proper flange seating. Provide your panel hole diameter, panel thickness and cable OD - our team recommends the exact size. Standard sizes cover ID 3mm-100mm, panel thickness 0.5mm-10mm.

Q3: Which material should I choose?

A3: By application environment: NBR - standard, cost-effective, excellent oil/abrasion resistance, -30~120℃. Best for general indoor electrical cabinets, machinery, automotive (oil-exposed). EPDM - excellent weather/ozone/UV resistance, waterproof, good insulation, -40~150℃. Best for outdoor, weather-exposed, high-voltage, solar/HVAC. Silicone - widest temp range (-60~230℃), food-grade option, soft/flexible. Best for high-temp, food/medical, extreme-temp. FKM (Viton) - excellent chemical/oil/heat resistance, premium, -20~200℃. Best for chemical processing, harsh industrial, high-performance automotive. CR - good all-around oil/weather/flammability resistance. When in doubt, contact our team with application details.

Q4: How to install? Do I need tools?

A4: No tools required - push-fit snap-in. Steps: (1) Drill correct diameter hole (hole saw, step drill or punch). (2) Deburr sharp edges and clean area. (3) Align grommet (flange outward) with hole from accessible side. (4) Push in by hand - elastic body compresses, snaps into place. (5) Verify flange is flat and grommet is secure (no rotation, no pull-out with moderate force). For large/firm grommets (80A, large sizes), gentle rocking or soft-faced mallet (with protective cloth) helps. Do not use sharp metal tools to pound. Takes 2-5 seconds per grommet.

Q5: Can you customize? What's the MOQ?

A5: Full customization available. Dimensions: ID 2mm-200mm+, OD 5mm-300mm+, custom height/flange/wall. Materials: NBR/EPDM/CR/Silicone/FKM, custom formulations (flame-retardant UL94 V-0, food-grade FDA, anti-static, conductive, high-temp). Hardness: 40-80A in 5-degree increments. Colors: Pantone matching. Designs: blind, multi-hole, stepped, ribbed, metal-bonded. MOQ: Standard stock (black NBR 60A) - 100 pieces, ships 3-5 days. Custom color of stock sizes - 500 pieces. Custom sizes (new mold) - 1,000-5,000 pieces per size, mold fee (refundable for 50,000+ orders). Lead time: 10-15 days custom production. OEM & ODM fully supported.

 

Why Choose Our Single Sided Protective Coils

 

One-side accessibility - installable where double-sided grommets cannot: Single flange, install from one side - ideal for enclosed cabinets, welded assemblies, deep housings, wall-mounted panels. Clean finished appearance on front panel.

Tool-free push-fit - 2-5 seconds each, no tools/adhesive/screws: Push into pre-drilled hole, elastic body locks. 10-30x faster than cable glands. Consistent installation quality. Removable and reusable.

Cable protection + insulation + dust seal + vibration damping: Smooth inner bore prevents insulation cut-through and short circuits (UL 508A/NEC/IEC compliant). Elastic body seals dust. Rubber insulates cable from panel. Vibration damping reduces cable fatigue. Four functions in one - metal/plastic grommets cannot match.

Multi-material / multi-hardness for every environment: 5 materials (NBR/EPDM/CR/Silicone/FKM), temp -60~230℃, oil/weather/chemical/food-grade options. Hardness 40-80A. 30+ standard sizes (ID 3mm-100mm) in stock. Same design works for indoor cabinets, outdoor solar, food processing, chemical plants, automotive.

Proven quality & full customization: Multi-stage inspection (material, dimensional ±0.1mm, visual, fit test, functional test), RoHS/REACH/UL94/FDA/SGS/ISO 9001. Full customization: dimensions, material, hardness, color, special features. In-house mold making (CNC+EDM) and compounding.

Factory-direct pricing & partnership support: No middleman markup, competitive pricing, 50,000+ pieces/day capacity. Standard sizes in stock (3-5 days), MOQ 100 pieces. Free consulting, samples, custom design, dedicated account management, JIT delivery, responsive after-sales. Long-term partnership.

Hot Tags: single sided protective coil, China single sided protective coil manufacturers, suppliers, factory

Send Inquiry

whatsapp

Phone

E-mail

Inquiry